Tuesday, December 6, 2022

How To Take Apart Original Xbox

Don't Miss

What You Will Need To Disassemble Your Xbox One Controller

ORIGINAL XBOX DISASSEMBLY [WARANTY VOID IF REMOVED]

Opening an Xbox One controller isn’t as easy as cracking open an old radio. You can’t use standard screwdrivers to get inside an Xbox One controller. Instead, you’ll need a Torx screwdriver—and that’s not all:

  • Torx screwdriver
  • Flathead screwdriver
  • Plastic prying tools
  • Plastic spudger or disposable knife

Don’t have all the tools needed to gain access to your Xbox One controller’s interior? Worry not—various Xbox One controller tool kits can be bought online.

To Help Keep Your Xbox One Fan Clean:

  • Use a can of compressed air to blast dust and dirt out of the air vents.
  • Once you’ve cleaned the vents, be sure to position your Xbox somewhere with good airflow to assist with cooling.
  • Clean your Xbox One console every three to six months to make sure it works like it should.
  • Give your Xbox the high groundâplace it somewhere off the floor and in the open rather than on a rug or inside a cabinetâto prevent heavy dust buildup. And keep it away from pets and small children that can cause messes or damage.

If cleaning out the vents doesn’t do the trick, we recommend calling in professional help to clean your Xbox One fan as it will require opening your console, which could easily lead to damage.

Xbox 360 Complete Tear Down Fix And Repair Video To The Point

How do I take apart my Xbox 360 to clean it?

To take apart your Xbox 360, you will need a T8 Torx screwdriver.First, remove the four screws on the back of the console. Next, remove the plastic cover on the front of the console. Be careful not to break it! Finally, remove the six screws on the top of the console and lift it off.

How do you open an original Xbox 360?

There are a few ways to open an Xbox 360. The most common way is to use a Torx T8 security bit to remove the screws on the back of the console. Once the screws are removed, the top of the console can be opened and the hard drive can be accessed.

What tools do you need to take apart an Xbox 360?

There are a few tools you will need in order to take apart an Xbox 360. You will need a T8 Torx screwdriver, a T10 Torx screwdriver, and a Y-shaped Torx screwdriver. You will also need a Phillips head screwdriver.

What do I do if my Xbox 360 tray wont open?

If your Xbox 360 tray wont open, the first thing you should do is check to make sure that there is no obstruction in the way. If there is, remove the obstruction and try to open the tray again. If it still doesnt open, you may need to take your Xbox 360 to a repair shop.

How do I clean the dust out of my Xbox 360 Slim?How can you fix the red ring of death?What is the Red Ring of Death on Xbox 360?How do you fix a dead Xbox 360?Can Xbox 360 be repaired?Is red ring of death fixable?Is the red dot of death fixable?Is the red ring of death real?

Read Also: How To Disconnect Xbox Controller From Xbox

How To Open Your Xbox

wikiHow is a wiki, similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time. This article has been viewed 113,102 times.Learn more…

If your old Xbox is starting to fail and youre thinking about repairing it yourself, or you want to install a modchip in it, the first step is opening the case. Luckily, with the right tools, opening the Xbox case is only a short process. Follow this guide to learn how.

Fully Teardown Your Xbox One Controller

Replacement Front Housing Shell for Xbox Series X Controller, Clear Re ...

Want to know more about how your Xbox One controller works? Consider a full teardown, stripping the device down to just the PCBs. You might even take this a step further and detach the triggers, thumbsticks, buttons, and more.

Be aware that a further teardown will expose electrical components. As such, you will need to take precautions to deal with the risk of static electricity damaging your controller.

Going further, four thin wires can be found on the left and right side of the controller . Two wires on each side are for the rumble motor, while the other four connect the two PCBs. These can be de-soldered with care, but this is only really necessary if you’re stripping it down for replacement components.

Related: Best Soldering Irons for Beginners

The PCBs, meanwhile, can be detached from the interior plastic chassis by removing four small screws.

Take care labelling and annotating the procedure, however, or else you’ll end up with a controller you can’t play with!

You May Like: How To Text Chat In Rainbow Six Siege Xbox One

The Good News: You Can Prolong The Life Of The Drive With Some Easy Fixes

Although the DVD-drive is subject to wear and tear, it consists of many replaceable / fixable parts. The laser can be cleaned, and a stuck DVD-tray can be fixed by replacing or cleaning a piece of rubber that is attached to the electrical eject motor. I usually combine these efforts with greasing some of the mechanical parts of the DVD-drive. This requires disassembling the Xbox, which will be further described below.

Don’t Let A Glitched Controller Mean Game Over

The Asurion Home+ protection plan offers peace of mind for all of your eligible home tech, including your favorite gaming systems, for less than $1 per day. From graphical glitches to faulty drives, we cover your video game console and original controller from the unexpected breakdownâno matter where or when you purchased it. Learn more at asurion.com/homeplus.

*The Asurion® trademarks and logos are the property of Asurion, LLC. All rights reserved. All other trademarks are the property of their respective owners. Asurion is not affiliated with, sponsored by, or endorsed by any of the respective owners of the other trademarks appearing herein.*

Keep your head in the game. Weâll handle the repairs.

If your console breaks down, our experts have your back. Make an appointment at your nearest store now.

Recommended Reading: How To Refund Xbox Live Gold

How To Clean An Xbox One

  • Unplug your console from the outlet and remove its power cable.
  • Use the microfiber cloth to wipe down the entire surface and exterior of your Xbox. Do circular motions to buff out fingerprints, smudges, and dirt.
  • Loosen the dust in and around the console’s ports, vents, and openings with the soft-bristled brush. You can also use the can of compressed air to blow away dust in these areas, but be sure to do only short bursts.
  • Grab your vacuum and hold the handheld attachment or hose near the console to remove any remaining dust in the console’s vents and ports.
  • Use the microfiber cloth to go over the Xbox’s surface one more time in case any dust has settled on top of it.
  • How To Open The Xbox One Or Xbox Series X/s Controller

    How To Take Apart An Original Xbox Controller S

    Before proceeding, ensure your Xbox One controller is powered off. Place it on a table or similar hard surface with the tools within easy reach.

    Follow these steps to open the Xbox One controller.

  • Remove the door to the battery compartment and set it aside.
  • Remove the batteries, saving them for later.
  • Using the plectrum or spudger, detach the plastic panels on the back of the controller’s “handles” where the controller sits in your hand. This can take a while, so take your time patiently wiggling the plectrum along each edge to unclip them.
  • With the controller face down, unscrew the five Torx screws. You’ll find two on the left, two on the right, and another beneath the label in the battery compartment. Put the screws aside safely for later.
  • The back panel should now simply lift off.
  • You can now lift out the main controller. Notice how this is a secondary plastic case, which houses a pair of PCBs .
  • At this stage you can now replace thumbsticks, D-pad, and the other buttons if you’re planning on some customizations.
  • Further disassembly at this stage requires some electronics knowledge so don’t proceed if you’re inexperienced with PCBs and electrical components .

    Congratulations—you’ve successfully taken apart your Xbox One controller.

    Also Check: How To Connect An Xbox Controller To An Ipad

    How To Put Xbox Games Back Together

    First, remove the hard drive from an Xbox, detach the power cord and plug it into an outlet. Then, drag the two screws on the back of the computer. Next, unscrew the top cover of the hard drive. Be careful not to damage the connectors on either side of the hard drive. Place the hard drive in a safe place and power up the computer.

    How To Take Apart Your Xbox One Controller

    Whether you want to customise, tear it down, or replace a thumbstick, you need to know how to open your Xbox One controller

    We put the Xbox One controller through a lot. Compatible with several devices as well as the Xbox One, this controller gets banged, dropped, and grimy. Hand grease, sweat, food, and other detritus can be found over the surface and in nooks and crannies.

    Then there’s issues with the feedback motors, buttons, and thumb sticks. In short, your Xbox One controller needs looking after. To do this, you need to know how to take apart the Xbox One controller, clean it, repair it, and reassemble it.

    Also Check: How To Fix Mic Echo Xbox One

    How To Disassemble An Xbox 360 For Cleaning

    UPDATE 7th July 2016 Twitter user @therealphydeux mentions the danger of using brushes on electronics. I should have mentioned when I made this guide that I use an anti-static wristband & workmat.

    Be warned, following these steps WILL void your Xbox 360 warranty. It is therefore advised that you only follow this guide if your console is older than 3 Years.

    Xbox 360 and supplies .

    This is a classic white Xbox 360 Premium. Usually it has a hard drive attached, however this one did not when it arrived for cleaning.

    Start by removing the front bezel. Pull from the bottom or the right-hand side .

    Following this step WILL VOID YOUR WARRANTY! Use you knife to carefully cut the warranty seal along the seam.

    Remove the bottom plastic grey vent. Pull from the front edge in one quick motion.

    Repeat the last step for the other end.

    Now grab your small, flat-head screwdriver.

    Insert the screwdriver as shown and with a force push down until you hear a click.

    Keep gently pulling apart the casing as you go.

    Here we see the rear of the case fully seperated.

    At the front the 360 you need to separate the locking tabs. I find this easier with the screwdriver but it can be done using just a fingernail. Again, gently separate the case as you move along.

    Lift off the bottom part of the case now and lay it flat, naked side facing up as shown.

    Remove the eject button, pulling it away from the right hand side. It may be quite stiff, but don’t worry.

    Time to get out the T10 Torx Driver!

    How To Take Apart Xbox One S

    Xbox Duke Controller

    To take apart your Xbox One S, youll need a T8 Torx screwdriver. You can find one online or at a hardware store.

    Once you have the screwdriver, follow these steps:

  • Turn off your Xbox One S and unplug it from the power outlet.
  • Remove the four screws on the back of the console using the T8 Torx screwdriver.
  • Gently lift the back panel off of the console.
  • Xbox One S is a gaming console that was released in 2016. The console is the successor to the Xbox One. The Xbox One S is a slimmer and more powerful version of the original Xbox One. The console has a built-in power supply and supports 4K Ultra HD video playback. The console also includes a redesigned controller that has Bluetooth support.

    Don’t Miss: How Much Is The New Xbox X

    How Do I Clean Dust From An Xbox One Without Opening It

    Once you have the necessary items, it’s easy to clean your gaming system and keep it looking greatâand you don’t even need to know how to open and clean an Xbox One to do so. Neither Microsoft® nor our experts advise taking your console apart because it does not have a removable faceplate. Here’s what to do instead:

    Performing Xbox One Controller Repairs

    Once you have successfully taken apart your Xbox One controller, you can attempt to make repairs. Some problems can be fixed by simply cleaning components, while other issues require you to replace components. In some cases, advanced skills like soldering are required to remove and replace components. Depending on your experience level, some of those repairs are better left to the professionals.

    Other fixes are much simpler, like repairing or replacing the d-pad ring. If your d-pad isn’t responding correctly, try this quick fix:

  • Use a prying tool or tweezers to carefully pop off the spring steel d-pad ring.

  • Carefully lift up the arms on the d-pad ring so that they apply more pressure, and reassemble. If that doesn’t fix your problem, you may need a new d-pad ring.

  • Read Also: How Many Xbox Series X Have Been Sold

    How To Use Xbox Games

    Xbox games can be played using a variety of methods. These include using the consoles keyboard and mouse or using the controller. To play a game, start by pressing the button on the controller that corresponds to the game you want to play. For example, press the friend button on your controller if youre going to play a game with friends. Once youve chosen a game, the press begins playing it.

    To exit the desired game, press the escape key or click on one of the buttons on your controller . If you lose track of where you left off in a game, dont worry Xbox has an option to restart it from where you left off.

    Xbox games come with various modes that allow for different gameplay depending on your type of gamer. These modes include a cooperative multiplayer mode in which players work together to complete objectives a competitive multiplayer mode in which players compete against each other for supremacy and a single-player mode in which players explore blocky levels while avoiding obstacles and enemies.

    In addition to these Modes, some titles are explicitly designed for one particular type of gamer or another. Titles like Gears of War 2, Halo 4, and Forza Horizon 4 are all designed for specific types of gamers who love action/adventure games and racing games.

    Reassemble An Xbox One Controller

    Xbox One: Teardown and Assembly

    When you’re satisfied the Xbox One Controller is ready to use again, simply follow the instructions above in reverse to reassemble the device.

    Whether you’ve cleaned it or made a repair, once reassembled your Xbox One controller should be working as normal once again. If not, consider buying a replacement controller, or looking at other troubleshooting steps.

    Read Also: Why Is Xbox Live Currently Unavailable

    How To Take Apart An Xbox Series X

    The modular design of the console makes the process extremely easy.

    Microsofts latest flagship console, the Xbox Series X, has been globally released with thousands of gamers bringing it into their home setups. New consoles are always an exciting time since gamers get a taste of whats possible with the superior technology inside.

    While getting a console on its release day is what most gamers intend to do, the first iteration of a new model is often prone to have issues that reveal themselves over time. Due to user wear and tear sometimes, its necessary to take the unit apart and inspect the internal parts to diagnose any issues.

    While its possible to do this yourself, we recommend sending the unit to be repaired by a professional, especially if the damage is claimable under warranty.

    Nevertheless, in some cases, theres no other option than looking for yourself. If it comes to that, here are the steps youll need to follow to take the Xbox Series X apart.

    Cleaning The Disc Drive/laser:

    Step 1. The disc drive will be the big gray square on the left side of the console, there are 2 plugs plugged into the back of the drive. These plugs need to be unplugged from the drive before you remove it completely. You can grab the drive on both sides and lift directly up to give you a little room to reach behind the drive and unplug the plugs. Then it should slide right out.

    Step 2. Using the small phillips head screwdriver, unscrew the 4 screws in the corners of the drive and SET THEM ASIDE SO YOU DON’T LOSE THEM

    Recommended Reading: Are Xbox One Controllers Bluetooth

    How To Clean Residue Off An Xbox Disc

    Use the microfiber cloth to wipe down both sides of the disc, especially the underside. You can add a small amount of rubbing alcohol to the cloth to buff out sticky spots, but be sure to let the disc completely dry before re-inserting it into your Xbox.

    That’s it! Once you’ve cleaned your Xbox One console, controllers, and discs, you can get back to enjoying the games you love.

    If you’ve tried these steps and still need a little help, we’re right around the corner. Schedule a repair at the nearest uBreakiFix® by Asurion or Asurion Tech Repair & Solutions⢠store and our certified experts can get your device back up and running as soon as the same day.

    How To Take Apart Xbox One

    Replacement Front Housing Shell for Xbox Series X Controller, Clear Re ...

    June 3, 2022 by Chidinma Kalu

    There are a few ways to change the aspect ratio on your device.

    The first way is to go into the settings of your device and look for an option called display. Within this menu, you should be able to find an option for adjusting the aspect ratio.

    Another way to change the aspect ratio is by using an app. There are a number of apps in the App Store and Google Play Store that allow you to change the aspect ratio.

    Also Check: How To Manually Eject Disc From Xbox One

    More articles

    Popular Articles