Friday, June 24, 2022

How To Disassemble Xbox One Controller

Don't Miss

Remove Torx Screw Behind The Battery Pack

How to take apart an Xbox One Controller

Located behind the battery pack cover is a sticker with device and warranty information. The middle of this sticker is covering a screw that is needed to separate the front, and back of the Xbox One controller.

This will void your warranty on the controller. Microsoft will not repair a controller or console that has been tampered with.;

Poke a hole in the sticker with your screwdriver. Remove the screw behind the sticker and set it aside in a safe place for when we reassemble the Xbox One Controller.

Reasons To Take Apart Xbox One Controller

If your Xbox Controller is not able to run there is definitely some problem. I hope you will try to fix it with the basic troubleshooting methods and have already updated the firmware.

You can take apart Xbox One Controller to do some more fixes. Here there are some reasons that lead to this type of problem.

  • Drifting analog Sticks To solve this, you can clean the analog sticks and if necessary, you can replace them.
  • Malfunctioning D-Pad To solve this, you can solve this problem by carefully pry up the tabs which are on the spring assembly. This will push down with more force, moreover, you can replace them if required.
  • Inoperable audio jack You can check the jack is properly set up or connected, replace them if required.
  • Sticking Buttons For this problem, you will need to clean it. You can use the canned air or any other method to remove the dust stick to it. It is possible after removing the circuit board assembly from the controller housing.

Read More: PlayStation 5: Everything You Need To Know About Sonys New console

Repair The Xbox One Controller Thumbstick

Various repairs can be performed once the Xbox One controller is open. Unresponsive buttons can be checked and thumbsticks repaired.

The Xbox One controller is prone to thumbsticks coming loose. In most cases this problem can be resolved by gluing a small pole of metal—perhaps from a thumbtack—into the thumbstick itself and pushing this into the analogue controller mounted on the circuit board.

You May Like: How To Breed Villagers In Minecraft Xbox One

Are You Coming Unstuck Thanks To Sticky Buttons Heres Something To Help

If sticky controller buttons are becoming a sticking point in your Xbox gaming progress, you might be wondering what you might be able to do to remedy the situation.

It can be more than a little annoying if pressing the jump button might make your character pogo around for a while, or reloading a gun becomes a nervous tic for your character. Especially if it culminates in you being unable to play your game properly.

So is there anything you can do to unstick a stuck button? Stick around, for some guidance.

How To Take Apart Xbox One Elite Controller

How to Take Apart an Xbox One Controller for Painting ...

bestbuy.com – Photo by bestbuy.com

If you own the Xbox One Elite console instead, youll notice that the controller is different from the standard one. Now if you want to know how to take apart Xbox One controller of this series, then follow these steps:

1. Prepare Soldering Iro, iFixit Opening Tools, T6 Torx Screwdriver, and T8 Torx Screwdriver along with the controller.

2. Remove the side panels with a pry tool.

3. Remove the 5 Torx Security Bit screws.

4. Pop the back panel off by prying the panel next to the 3.5mm port.

5. Carefully remove the ribbon so that you wont rip the ribbon cable. You can pop the connector up to remove the ribbon easily.

6. Screws on controller motherboard by removing the 2 Torx screws.

7. Desolder wires from motherboard. Do it to the 4 wires on each side, these control the vibrations and the RT LT.

8. Remove the motherboard by pulling up from the “top” side of the controller on the sister board.

9. Remove the Home Button Cover. Be careful not to lose the sync button. Do so by prying the middle section up from the home button side. Note that this will also remove the LB and RB which is a single part.

10. Remove the controller daughterboard by unscrewing the 6 Torx screws.

11. Youve successfully dissembled your Xbox One Elite Controller.

Recommended Reading: How To Enable Cross Platform Fortnite Xbox

How To Take Apart Xbox One Controller Diy With Torx Screwdrivers

How to Take Apart an Xbox One Controller / xbox one controller disassembly Just like other devices that have ever existed,

your Xbox controller may experience troubles at some points.

The joystick might be stuck or the d-pad might get disordered.

In these cases, theres a chance that you will need to disassemble it in order to fix the item.

If you want to know how to take apart an Xbox One controller in easy and quick way, read the following guide.

How To Open An Xbox One Console

This article was written by Jack Lloyd. Jack Lloyd is a Technology Writer and Editor for wikiHow. He has over two years of experience writing and editing technology-related articles. He is technology enthusiast and an English teacher. This article has been viewed 294,614 times.

This wikiHow teaches you how to open your Xbox One console’s internal casing. Doing this will void your warranty. This article will not teach you how to open an Xbox 360 console.

Read Also: Why Wont My Xbox 360 Controller Turn On

Ready To Game Remember To Wash Your Hands First

After cleaning your Xbox One controller inside and out, it makes little sense to let it get dirty again. You’ve taken the time and effort with a deep clean, after all.

So, rather than simply grab the controller and boot your Xbox One or Xbox Series console, stop. Instead of playing straight away, go and wash your hands thoroughly. No sink nearby? Use anti-bacterial gel designed for hands. If you’re gaming regularly, consider a gel intended for sensitive skin.

Enjoy your gaming session and strive to keep your controller clean. When you’re done, clean the controller with an anti-bacterial wipe and remember to wash your hands again.

Clean Inside The Xbox Controller

How to Open/Disassemble an Xbox One Controller (Part 2)

The next stage is to clean the interior body of the Xbox One controller.

This means wiping around the buttons and lifting them off if necessary. The same applies to the D-pad and thumbsticks.

Shoulder buttons and triggers should also be cleaned. Take care here, as pushing in the wrong way can detach the mechanism. Similarly, the rumble motors should also be gently cleaned as these can pick up dirt and dust.

Don’t Miss: How To Hook Up Bluetooth Headphones To Xbox One

How To Disassemble Xbox One Controller Easily

The Xbox has been in high demand for the past decade. Microsoft had introduced this game back in 2001, and since then, it has become the dream of every child to own the Xbox. After the lockdown, especially, it has been one of the highly purchased online gaming platforms. In this article, we will discuss how to disassemble the xbox one controller

There are five versions of Xbox. Each has unique features that make it stand out.

You might sometimes face some issues when it comes to taking care of your Xbox. If you use it excessively, there is a chance that it will get spoilt. Apart from that, there is a shell-life of electronics, so if you are facing issues even when you use the controller properly, you do not have to worry.

This issue is always solvable, provided you follow the procedure. This article will help you to comprehend how to disassemble the xbox one controller straightforwardly. Make sure that you spend enough time understanding the technique. This will help you to perform it in a better way.

Got To Clean Or Fix The Stuck Joystick Just Take Apart The Xbox One Controller With Our Simple Diy Tips

With Xbox One, Microsoft let its users experience the best of gaming and entertainment. Xbox One will take your gaming skills to a whole new level. You will be able to play like a pro with a wide range of digital games it has. Without the Xbox One Controller, you will not be able to get to know the real fun of playing Xbox One games. The controller is the most essential thing to control the gameplay. Xbox One controller holds a sync button, two analog triggers, analog sticks, ten digital buttons, and a digital D-Pad. Besides this, there is a guide button with which you will be able to turn on the console or the controller. For any reason, if you consider disassembling the Xbox One controller, then we will guide you step-by-step. Take a look at how to take apart the Xbox One controller in brief.

FYI! For any reason, Microsoft doesnât recommend you open the Xbox One gaming controller. It recommends you to look for professional help in order to deal with internal repairs. Be cautious as damaging the parts may void the warranty.

Don’t Miss: Find Xbox Ip Address From Computer

How To Disassemble Xbox One Control Without Tools

It is advisable that you do not invest any money to purchase expensive tools that claim to help you resolve how to disassemble xbox one controller within minutes. First, you should try the methods that will help you resolve this without any investment needed. This article will present some easy steps that you should follow as they have been set out. It is advised that you understand the steps and then perform them.

The first step to solve how to disassemble the xbox one controller is to take out the consoles battery. This will be at the back of the controller; make sure that you keep the battery properly. After that is done, you will have to proceed then to remove the sides of the controller.

It is vital that you do this first, or else you cannot gain control of the Torx screws. Even a small trim tool will work if you want to do this or any other tool will work just fine. This will not spoil the plastic of the console. Next, you should remove the sides very easily and swiftly. Some time will have to be spent in finding the perfect edge. After that, you can slowly open the game console. Know about the best xbox one emulator for pc from this article!

You are already closer to resolving how to disassemble the xbox one controller without any technical expertise.

How can it ever get easier than this?

See also: 10 Best Xbox One Emulators For PC And Mac | 2021

Learn How To Fix Your Pesky Xbox One Or Xbox Series X Controller From Drifting And Disrupting Your Gameplay

How to Take Apart an Xbox One Controller

Picture this: youre toddling off to find your next side quest, and suddenly your character veers off to the right instead of forwards. Or maybe youd like to stand still for a second to take in your surroundings, but your in-game protagonist has other ideas. Annoying, right?

Dont worry your pixelated hero hasnt become sentient. The more likely explanation is a phenomenon known as stick drift. While more commonly associated with the PlayStation 5s DualSense or the Joy-Cons, this can also happen to the Xbox controller, as the three controllers all use essentially the same joystick design. This is where your controllers analogue stick fails to centre itself properly after a directional push, resulting in involuntary camera or character movements.;

This issue is generally caused by wear and tear, and shouldnt happen with a new controller. But the good news is that it can be fixed. There are two ways of doing this one is easy and doesnt involve opening your controller up; the other does.

So, heres how to fix stick drift on your Xbox One or Xbox Series X controller.

Don’t Miss: Does The Razer Nari Essential Work On Xbox One

Safely Disassemble Your Xbox One Controller For Easy Fixes

The Xbox One controller is generally accepted as one of the best video game controllers around, but they still break down and need repairs from time to time. While you can take apart an Xbox One controller without too much trouble, there are a few potential snags to be aware of, and you’ll also need a couple specialized tools that you may not already have laying around.

Complete Instructions To Apart Xbox One Controller

#1 Remove the Battery Cover from the back of the Xbox One Controller

  • Switch back to the Xbox One Controller.
  • Hold the Battery Cover and Slides it up to remove it. Keep the battery cover on the tray
  • Now remove the Battery and empty the battery case.

#2 Open Both Side Grip Panels

  • Pick up the flathead Screwdriver or a Spudger.
  • Hold your Xbox Controller firmly.
  • Wedge the screwdriver or spudger between the Controller and Grip seam.

  • Start prying the Grip Panel from the Controllers other panels until its completely removed from the Xbox One Controllers.
  • Do this for the second grip and keep both the grips safe into the tray.
  • Dont be so hard on prying; keep it smooths otherwise you will end up with a broken grip. And you will have to play like that only.

Now that you have removed the Battery and Both Side Grip Panels its time to go inside the Xbox Controller. Just keep following the instructions.

#3 Unscrew the Front Faceplate Cover

#4 Pull off Back Panel from Xbox One Controller

The Back panel will automatically be pulled off once all the 5 screws are unscrewed and tap out from the Xbox Controller.

Keep the back panel in the tray. Now you will be able to see the motherboard and other parts inside the Xbox One Controller. Congratulation you are halfway through.

#5 Uncover Bumper Button Cover

#6 Remove Upper Mother Board from the Xbox Controller

#7 Remove the bottom motherboard from Xbox one Controller

Read More:

Recommended Reading: How To Change Xbox Name On App

How To Take Apart A Microsoft Xbox One Controller

The process for opening the Xbox One controller is straightforward with the right tools.

  • Remove the battery cover and any batteries
  • Remove the grip plastic
  • Unscrew the five Torx screws
  • Lift the rear cover from the controller
  • Lift the internals away from the front fascia

Below we’ll go through the steps in more detail. Note that opening a first generation Xbox Series X/S controller follows the same procedure.

How To Clean Your Xbox Controller Without Taking It Apart

How to Take Apart an Xbox One Controller

Most Xbox controller cleaning jobs require nothing more than an external sweep. Still, even if your controller seems relatively clean, you should give it a full cleaning. Sweat and dust can easily build up in the crevices of your controller, and although you may not see the buildup, its almost certainly there. Heres what youll need to clean your Xbox controller without taking it apart:

  • Cotton swabs
  • Isopropyl alcohol
  • Canned compressed airl
  • Spray bottle

You may need water as well, depending on the percentage of your isopropyl alcohol. In order to be considered rubbing alcohol, a bottle of isopropyl alcohol needs to be at least 70% alcohol to 30% water. If your bottle has a higher percentage, you may need to dilute it with water. Dont go overboard, though; isopropyl alcohol is still the recommended cleaning medium.

Don’t Miss: Jtagging An Xbox 360

Rubbing Alcohol And Cotton Buds

A simple, non-invasive approach, this combination can be effective if you are just starting to notice some stickiness. It is likely that a minor clean will be sufficient to remedy your problem.

  • Make sure your controller is unplugged.
  • Dip the cotton bud into the rubbing alcohol, and rub off any excess. You dont want too much.
  • Rub the cotton bud around the sticking button, and get as far into the crevices as you can. The alcohol will help to break down any gunk that has built up.
  • After going around the button several times, press the button repeatedly, to allow the alcohol to work its way further into the mechanism. Pressing should also help to loosen any residual dirt.

Leave the controller to dry. Rubbing alcohol should dry relatively quickly, and the small amounts you are using should not do damage to the internal circuitry of the controller.

How To Take Apart An Xbox One Controller

  • Consider working on a tray to prevent screws or other parts from falling on the floor or getting lost.
  • Take the orange pry tool from your tool kit.
  • Slide the pry tool between the plastic seam on the grips as shown.

  • Lever the grip away from the main controller body. Note that there is also adhesive holding it in place under the plastic, so don’t be afraid of applying some force.
  • Repeat this again for both grips.
  • Next, we’ll remove the screws. Once the screws are removed, your Xbox controller will come apart like a sandwich. Be extremely careful because if you pull it apart too hard, you may damage the cable that connects the battery to the circuitry.

  • Find your T8 screwdriver from your kit, and begin removing the five security screws as shown. Note that one of the screws is hidden behind the sticker in your battery housing.

  • Now, you can take a look at the inner workings of your gamepad. Take care not to misplace any of the parts, though!

    Also Check: Warzone Keeps Crashing Xbox

    Repair And Replace The Thumbstick

    Once the Xbox One controller is open, you can conduct a variety of repairs. Fixing unresponsive buttons with additional cleaning and thumbstick repair are examples of this. In most situations, this problem may be resolved by soldering a short metal rod into the thumbstick and inserting it into the circuit board’s analog controller.

    More articles

    Popular Articles